What does a geyser repair cost in Nellore?

A geyser repair in Nellore through us costs ₹399 for the visit, diagnosis and standard labour on a no-hot-water or thermostat fault, ₹350 for a leak, and ₹399 for anything that does not fit those neatly. A new installation is ₹699 and a safe removal is ₹399. Parts are on top at MRP, shown before fitting. That is the whole structure; the rest of this guide is what sits behind each figure so the bill does not surprise you.

The rate card

Job	Diagnosis + labour	What the visit covers
No hot water	₹399	Element, thermostat, cut-out and PCB diagnosis; fit the part
Water leaking	₹350	Anode rod, relief valve, fittings, gasket, tank assessment
Thermostat fault	₹399	Replace thermostat and set temperature
New installation	₹699	Bracket mount, plumbing connections, electrical hook-up and earth check
Uninstallation	₹399	Drain, remove, cap off plumbing safely
Any other fault	₹399	General geyser repair entry on the rate card

What "standard labour" means

The work a technician can do on the spot with the tools carried: drain the tank, pull and replace an element or its gasket, swap a thermostat or thermal cut-out, change the relief valve or the anode rod, clean and tighten a corroded terminal, reseat a fitting, descale an element, check earth continuity and the RCCB. Most geyser faults are exactly this, and the visit plus one part is the usual bill.

What it does not include: running new wiring to the bathroom, fitting a new socket or RCCB in the distribution board, extending plumbing to a new position, or chasing a wall. Those are quoted separately, in writing, before anything starts — often with the electrician or plumber rate card rather than the geyser one.

How parts are priced

Parts are charged at MRP. The technician shows you the old part that came out and the new one going in, with its price, and you approve before it is fitted. Without quoting figures we do not control, the rough order is:

• Small parts: thermostat, thermal cut-out, element gasket, relief valve, anode rod, a fitting or flexible hose. With one of these the bill stays modest.
• Middle parts: heating element (varies with wattage and brand), flow switch on an instant geyser, a multifunction valve.
• Expensive parts: the digital control board on a touch-panel geyser. This is the one that turns into a repair-or-replace conversation on a cheaper unit.

If the diagnosis is the tank, there is no part to quote — it is a new geyser — and you pay the visit fee only.

What makes the bill lower

• You have done the safe checks — switch, socket, MCB once, thermostat knob, where the drip is from — and can tell the technician.
• You booked the closest fault. A leak and a no-hot-water call are different kits.
• The fault needed no part at all, which happens more than people expect: a tripped cut-out after a thermostat was set too high, a loose terminal, a scaled element that cleans up.
• The tank has been flushed in the last year, so the element comes out without a fight.

What makes it higher

• The geyser ran for weeks taking longer and longer; the scaled element has now failed and the tank needs a heavy flush before the new one goes in.
• A leak at the element flange was ignored until the terminal block corroded, so the job is gasket plus terminals plus a socket.
• The RCCB was bypassed to stop it tripping, and the element has been leaking current into the water for months. The element is the same price; the lecture is free.
• The installation was wrong from the start — 4.5 kW instant geyser on a 10 A MCB and thin wire — and the real fix is electrical.

What is not charged

• No advance. You pay when the job is done.
• No charge for declining a quote. If the answer is "the tank is gone" and you decide to buy new, the visit fee stands and nothing more.
• The repair carries a written 30-day warranty on the labour and the specific fault fixed. Same fault back inside that, fixed free, parts included.

Worked examples

A six-year-old 15 L geyser: lamp on, water cold. Element open-circuit, scale on it like a shell. Tank drained and flushed, new element and gasket fitted, anode checked and still fair. Bill: ₹399 plus the element at MRP, shown first.

Steady drip from the relief valve all day. Valve not reseating on grit. New valve, drip line checked. Bill: ₹350 plus the valve.

Water scalding, then nothing. Thermostat stuck closed, cut-out tripped. Thermostat replaced and set to 55°C, cut-out reset and tested. Bill: ₹399 plus the thermostat.

Nine-year-old geyser, rusty water from the bottom cover. Tank corroded through. Written advice to replace; no part quoted. Bill: ₹399 for the visit and a clear answer. The family books uninstallation and a new installation for the following week, ₹399 and ₹699.

Booking the right job

Pick the symptom closest to yours from the table; if none fits, book the general geyser repair. Mention storage, instant or gas, the litres, the rough age, and whether you are on borewell water. Those four details are most of what the technician needs to arrive ready.